How to Read a Maine Cannabis Lab Report in Two Minutes

Most people never look at a lab report. They look at one number on the jar and move on. That's a shame, because the full report, the COA (certificate of analysis), tells you a lot more, and it only takes a couple of minutes once you know where to look.

Here's how I read one. Budtenders, this is the version you can walk a customer through at the counter.

First, check that it's the right report

Before anything else, make sure the report matches the jar. A COA should name the lab, the product or strain, and a sample or batch ID. Look for that ID on the package. If they don't line up, the rest of the report doesn't tell you anything about what's in your hand.

Then look at the dates. You'll usually see when the sample was collected and when the lab finished testing. An older report isn't wrong, but it's describing flower that's been sitting since then. Freshness is its own topic, and we'll get into it in a later post.

The pass/fail part: did it clear the state's screens

In Maine's adult use program, flower has to go through mandatory testing before it can be sold. The state's list for flower covers filth and foreign material, dangerous molds and mildews, harmful microbes, cannabinoid potency, water activity and moisture, and heavy metals like lead, arsenic, cadmium and mercury. Flower in its final form for sale also gets tested for pesticides.

On most reports, each of those shows up as its own section with a pass or fail. You'll also see "ND," which means not detected, and "<LOQ," which means there was so little the lab couldn't reliably measure it. On a contaminant line, ND is what you want to see.

If you only have ten seconds, this is the part to check. Every category should say pass.

The numbers: water activity, potency and terpenes

Water activity is the number most people skip. It's a measure of how much free water is in the flower. It's not quite the same thing as moisture content, which is the share of the weight that's water. Maine's testing covers both.

Water activity matters because it tells you how well the flower was dried and cured. Too high and mold has room to grow. Too low and the flower gets brittle and dusty in the jar. It's one of the few lines on the report that says something about how the grower handled the crop after harvest, which is where a lot of quality is won or lost.

Potency is the section everyone jumps to. It lists each cannabinoid the lab measured, then adds them up. We talk about that total as TAC, total active cannabinoids, because it's a fuller picture than any single compound.

Watch the units. Some reports give percent, some give milligrams per gram, and some give both. 10 mg/g is the same as 1 percent, so 220 mg/g is 22 percent. People get tripped up by this all the time.

Then move on. I've written before about why the number on the jar is one of the least useful things on the label. A higher total doesn't make one jar better than another.

Terpenes are the part that's actually about the flower. Not every report includes them, because the state doesn't require them for flower. When they're there, this is where I spend my time. The terpene section lists the aroma compounds the lab found and how much of each. If you've read our Terpenes 101 post, this is the lab's version of what your nose is already telling you.

A report with a solid terpene total and a clear lead terpene tends to go with a jar that smells like something when you open it. That's a better quality signal than potency.

Two minutes at the counter

If a customer asks about a lab report, here's the order I'd walk them through:

  • Match it. Same batch ID as the jar, and note the test date.

  • Check the passes. Every required category should say pass.

  • Look at water activity. It's a clue to how the flower was dried and cured.

  • Read the potency units, then don't dwell on them.

  • Find the terpenes if they're listed. That's where the character is.

Then hand them the jar and let them smell it. The report and the nose should agree.

Ask your budtender or us for the COA on any batch. See what we're growing now on our Strains page.

Next
Next

What "Living Soil" Means, and What It Changes in the Jar